Mobile Tyre Fitting in Teignmouth

What we can do in Teignmouth

• Mobile tyre fitting — supply and fit a replacement at your home, workplace or the roadside, including balancing and disposal of the old casing.
• Mobile puncture repair — where the damage is inside the repairable area of the tread, a repair is cheaper and quicker than replacement.
• Commercial tyre fitting — vans, minibuses and other light commercial vehicles.

Stuck in Teignmouth right now? Call 07989 606060 and we will tell you what we can do and what it will cost before we set off.

Before we arrive

• Find your locking wheel nut key. Without it the wheel cannot come off. It is usually in the glovebox, the boot well, or with the spare.
• Read your tyre size off the sidewall, for example 205/55 R16 91V, so we arrive with the right tyre rather than making a second trip.
• If you are on a motorway or dual carriageway, get as far left as you can or into a refuge, then everyone out through the passenger doors, over the barrier and well back from the carriageway — not in the car. Ring with the junction number and your direction of travel.
• Describe where you are, not just your postcode. A junction number, a bay number, a farm, a pub or a bridge puts us on the spot far faster — rural postcodes can cover a mile of near-identical lane. We bring our own lighting, so darkness is not a problem.

More detail in our guides on what to do with a flat tyre on the motorway and checking your tread depth.

Repair or replace

Whether a tyre can be repaired is decided by where the damage is, not by how big the hole looks. Damage inside the central three-quarters of the tread, up to 6mm across, is repairable under BS AU 159. Damage in the shoulder or the sidewall is not, at any size — there is no way to reinforce a sidewall that flexes on every revolution.

The other thing that rules out a repair is having driven on the tyre flat. A short distance is enough: the sidewall folds under the rim and the internal cords break. That often does not deflate the tyre at the time — it shows up days later as a soft rounded bulge, and a tyre in that condition has to be replaced whatever the original puncture looked like.

How the damage was made matters as much as where it is. A nail or a screw pierces, leaving a neat hole that is usually well within the limit. Flint, crushed stone, quarry aggregate and dropped stainless fixings cut instead — a gouge or a tear rather than a puncture — and a cut frequently exceeds the repairable size even when it lands squarely in the middle of the tread. That is why we take the tyre off and look inside before telling you either way, rather than judging it from the outside.

Impact damage behaves the same way. A pothole or a kerb taken at speed compresses the suspension fully and pinches the sidewall between the rim and the obstacle. If that has happened, check both tyres on that side — the rear takes the same hit a fraction of a second after the front — and look for a bulge rather than for a hole.

We carry both outcomes to every job, so a repair that turns out not to be safe does not become a second visit.

Age and wear

Tread depth is not the only thing that retires a tyre. Rubber hardens as it ages whatever the mileage, which is why a caravan, motorhome, trailer or second car can carry almost full tread on a casing that is well past useful life. The four-digit date code on the sidewall gives the week and year it was made — our guide on how long tyres last covers where the line falls.

Depth matters most in standing water. The legal minimum is 1.6mm across the central three-quarters, but a tyre's ability to clear water falls off well above that — by about 3mm you are losing it noticeably, and aquaplaning starts at lower speeds than most drivers expect. Our tread depth guide covers checking it with a 20p coin in about a minute.

Wear patterns are worth reading too. Both outer shoulders going before the middle usually means underinflation, or a lot of cornering and hill descent; one edge alone is more often alignment. We will tell you which it looks like when we are there — see uneven tyre wear for the full picture.

Vans and light commercials

A van needs a tyre carrying the C marking and the correct load index. That is not interchangeable with a passenger tyre of the same nominal size, whatever may have been fitted before — the casing is built to carry more, and a loaded van on passenger-rated tyres is running outside the rating.

Tell us whether the van is loaded when you ring, and we will bring the right fitment first time. Details of what we carry are on the commercial tyres page.

How the repair is done

The wheel comes off, the tyre comes off the rim, and the inside of the casing is inspected before anything else happens. The puncture is then repaired from within using a combined plug and patch, and the wheel is balanced before it goes back on.

That inspection is the part that matters. An external plug pushed into the tread without removing the tyre is a get-you-home measure: it can seal the hole while leaving damage inside the casing entirely undetected, and that damage is what causes tyres to fail later at speed. It is the same job a garage does, done where the vehicle already is.

A slow leak with no puncture to find

A tyre that loses air over days with nothing in the tread has usually failed at the seal rather than the surface — a corroded alloy bead seat, or a perished valve stem. Neither can be found with the tyre still on the rim, and neither is fixed by topping the pressure up.

It typically announces itself on the first cold morning of the year. Cold air contracts, dropping the pressure a few PSI, and a leak that was tolerable through mild weather is a visibly flat tyre by the time you come out to the car. The fix is the tyre off the rim, the sealing face cleaned back to sound metal, and a new valve.

Working conditions around Teignmouth

Salt. Sea air corrodes far harder than road salt does, and it works on the parts of a wheel you cannot see. Pitted alloy bead seats and corroded valve stems are the standard coastal fault, and they present as a slow leak with no puncture anywhere in the tread. Vehicles parked near the front year round get it worst.

Gradients. A sustained climb builds heat in the casing, and heat finds whatever weakness is already there — which is why underinflated or previously damaged tyres are the ones that let go on a long pull rather than on the flat. On a steep slope we will ask to move onto level ground before jacking: a handbrake holds two wheels, and that margin drops sharply the moment one of them comes off the ground.

Common questions in Teignmouth

My tyre has gone on the Shaldon bridge.

Keep going slowly to the far side if you possibly can. Stopping on it shuts the only crossing for miles, and there is no width to work in.

Can you come onto the docks?

Yes, with access arranged through the port beforehand. Tell us when you ring rather than when we arrive.

Can you work on the hill roads?

Sometimes. They are steep, narrow and parked both sides, so we will often suggest meeting on the level near the Den or the station.

Slow leak and I park near the sea wall.

Salt spray corrodes the rim where the bead seats. We clean the sealing face back to metal and reseat the tyre.

Do you cover Shaldon, Bishopsteignton and Holcombe?

Yes, across TQ14.

Not in Teignmouth?

We cover the rest of Devon and beyond. If you are closer to one of these, the same service and the same number applies:

• Mobile tyre fitting in Barnstaple
• Mobile tyre fitting in Bideford
• Mobile tyre fitting in Brixham
• Mobile tyre fitting in Dawlish
• Mobile tyre fitting in Exeter
• Mobile tyre fitting in Exmouth
• Mobile tyre fitting in Honiton
• Mobile tyre fitting in Ivybridge
• Mobile tyre fitting in Newton Abbot
• Mobile tyre fitting in Paignton
• Mobile tyre fitting in Plymouth
• Mobile tyre fitting in Tavistock

See every area we cover.