Mobile Tyre Fitting in Blythe Bridge

What we can do in Blythe Bridge

• Mobile tyre fitting — supply and fit a replacement at your home, workplace or the roadside, including balancing and disposal of the old casing.
• Mobile puncture repair — where the damage is inside the repairable area of the tread, a repair is cheaper and quicker than replacement.
• Commercial tyre fitting — vans, minibuses and other light commercial vehicles.

Stuck in Blythe Bridge right now? Call 07989 606060 and we will tell you what we can do and what it will cost before we set off.

Before we arrive

• Find your locking wheel nut key. Without it the wheel cannot come off. It is usually in the glovebox, the boot well, or with the spare.
• Read your tyre size off the sidewall, for example 205/55 R16 91V, so we arrive with the right tyre rather than making a second trip.
• If you are on a motorway or dual carriageway, get as far left as you can or into a refuge, then everyone out through the passenger doors, over the barrier and well back from the carriageway — not in the car. Ring with the junction number and your direction of travel.
• Describe where you are, not just your postcode. A junction number, a bay number, a farm, a pub or a bridge puts us on the spot far faster — rural postcodes can cover a mile of near-identical lane. We bring our own lighting, so darkness is not a problem.

More detail in our guides on what to do with a flat tyre on the motorway and checking your tread depth.

Repair or replace

Whether a tyre can be repaired is decided by where the damage is, not by how big the hole looks. Damage inside the central three-quarters of the tread, up to 6mm across, is repairable under BS AU 159. Damage in the shoulder or the sidewall is not, at any size — there is no way to reinforce a sidewall that flexes on every revolution.

The other thing that rules out a repair is having driven on the tyre flat. A short distance is enough: the sidewall folds under the rim and the internal cords break. That often does not deflate the tyre at the time — it shows up days later as a soft rounded bulge, and a tyre in that condition has to be replaced whatever the original puncture looked like.

How the damage was made matters as much as where it is. A nail or a screw pierces, leaving a neat hole that is usually well within the limit. Flint, crushed stone, quarry aggregate and dropped stainless fixings cut instead — a gouge or a tear rather than a puncture — and a cut frequently exceeds the repairable size even when it lands squarely in the middle of the tread. That is why we take the tyre off and look inside before telling you either way, rather than judging it from the outside.

Impact damage behaves the same way. A pothole or a kerb taken at speed compresses the suspension fully and pinches the sidewall between the rim and the obstacle. If that has happened, check both tyres on that side — the rear takes the same hit a fraction of a second after the front — and look for a bulge rather than for a hole.

We carry both outcomes to every job, so a repair that turns out not to be safe does not become a second visit.

Age and wear

Tread depth is not the only thing that retires a tyre. Rubber hardens as it ages whatever the mileage, which is why a caravan, motorhome, trailer or second car can carry almost full tread on a casing that is well past useful life. The four-digit date code on the sidewall gives the week and year it was made — our guide on how long tyres last covers where the line falls.

Depth matters most in standing water. The legal minimum is 1.6mm across the central three-quarters, but a tyre's ability to clear water falls off well above that — by about 3mm you are losing it noticeably, and aquaplaning starts at lower speeds than most drivers expect. Our tread depth guide covers checking it with a 20p coin in about a minute.

Wear patterns are worth reading too. Both outer shoulders going before the middle usually means underinflation, or a lot of cornering and hill descent; one edge alone is more often alignment. We will tell you which it looks like when we are there — see uneven tyre wear for the full picture.

Vans and light commercials

A van needs a tyre carrying the C marking and the correct load index. That is not interchangeable with a passenger tyre of the same nominal size, whatever may have been fitted before — the casing is built to carry more, and a loaded van on passenger-rated tyres is running outside the rating.

Tell us whether the van is loaded when you ring, and we will bring the right fitment first time. Details of what we carry are on the commercial tyres page.

How the repair is done

The wheel comes off, the tyre comes off the rim, and the inside of the casing is inspected before anything else happens. The puncture is then repaired from within using a combined plug and patch, and the wheel is balanced before it goes back on.

That inspection is the part that matters. An external plug pushed into the tread without removing the tyre is a get-you-home measure: it can seal the hole while leaving damage inside the casing entirely undetected, and that damage is what causes tyres to fail later at speed. It is the same job a garage does, done where the vehicle already is.

A slow leak with no puncture to find

A tyre that loses air over days with nothing in the tread has usually failed at the seal rather than the surface — a corroded alloy bead seat, or a perished valve stem. Neither can be found with the tyre still on the rim, and neither is fixed by topping the pressure up.

It typically announces itself on the first cold morning of the year. Cold air contracts, dropping the pressure a few PSI, and a leak that was tolerable through mild weather is a visibly flat tyre by the time you come out to the car. The fix is the tyre off the rim, the sealing face cleaned back to sound metal, and a new valve.

Working conditions around Blythe Bridge

Level crossings. A vehicle stopped on a crossing is an emergency, not a breakdown. Get everybody out and well clear on the far side from the barriers, then use the railway telephone at the crossing, or ring 999 and ask for the railway, before you ring anybody else. Only the signaller can stop a train, and that has to happen before anything else does.

Common questions in Blythe Bridge

My tyre has gone down in the queue at the barriers.

Tell us which side of the railway you are on. The way round to the other side is a long detour, so approaching from the wrong one costs far more time than it sounds like it should.

Is the station an easy place for you to reach?

Yes, as long as we know which approach you are on. The crossing separates the two platforms and the two halves of the village, so name the road as well as the station.

I came off the A50 and stopped on the slip road.

Say which slip and which direction you were travelling. If the wheel will carry the car into the village at all, that is a far better place to wait for us than a slip road.

How often do the barriers come down?

Trains run about hourly each way with freight as well, so several times an hour at the busier parts of the day. It is worth factoring into any estimate either of us gives.

Do you cover Forsbrook, Draycott and Caverswall?

Yes, across ST11 and out into the lanes east of the village.

Not in Blythe Bridge?

We cover the rest of Staffordshire and beyond. If you are closer to one of these, the same service and the same number applies:

• Mobile tyre fitting in Barlaston
• Mobile tyre fitting in Biddulph
• Mobile tyre fitting in Brewood
• Mobile tyre fitting in Burntwood
• Mobile tyre fitting in Burslem
• Mobile tyre fitting in Burton upon Trent
• Mobile tyre fitting in Cannock
• Mobile tyre fitting in Cheadle
• Mobile tyre fitting in Cheddleton
• Mobile tyre fitting in Cheslyn Hay
• Mobile tyre fitting in Codsall
• Mobile tyre fitting in Eccleshall

See every area we cover.